🎈 Public Lab: Revisions for 'Oil Testing Kit'

Revisions for Oil Testing Kit

131	warren	July 23, 2014 00:19 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno, swabbing a street grate by @warren Preparing samples Use a cotton swab or small brush, dipped in mineral oil, to break up some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. Wear gloves before handling suspected pollutants. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Where possible, try not to put too much sand or other stuff in the jar. Save extra samples in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means (see Validate your results below). Seal the bottle tightly with the cap. You can then gently turn it over a few times to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Now that your sample is prepared, you may be able to get it to fluoresce by shining an ultraviolet light through it. We have had good results using a blue/UV laser, a 405 nanometer laser which is the same as found in a Blu-Ray player. See the parts list below for where to buy one. Strong UV LEDs can also work, but are not as bright. They are, however, easier to line up with a spectrometer's opening slit. Don't look at the laser too much, as it can hurt your eyes, even if you're not pointing it directly at your eye! Note that the laser will have a purpleish color by itself (as seen in the lead image at the top of the page) -- this is not fluorescence, but just scattering of the laser light. What you're looking for is any other color -- whitish, bluish, greenish -- which is not from the laser, but is produced in the material itself as it's excited by the UV light. To measure precisely the colors that are being produced, we will use a spectrometer. Spectrometry Colored light is often a blend of different colors. A spectrometer is a device which splits those colors apart, like a prism, and measures the strength of each color. A typical output of a spectrometer looks like this; [illustration of spectrometer plot] While there are many ways to use a spectrometer, in this case we can clearly see the laser color, or wavelength, which is only in a narrow range around 405 nanometers, to the left: [image here] All the remaining light, to the right of that tall peak, is produced by the excited material in the sample. The shape of that curve can be matched against other samples to help us identify what ours is. Construct a spectrometer different kits, download still under development Illuminate the sample cover it! no room or daylight good exposure no clipping Refine your technique same concentration take several for each, label them smooth your data repeat twice through and ensure your same samples are similar (ref. parts & crafts sample) concentration is OK? Compare When identifying an oil, we are hoping to measure the color of fluorescence of the Poly-Aromatic Hydrocarbons (PAHs) in the sample. The best way to identify a sample would be to compare it to a selection of similarly-prepared known reference materials. For example, if you have unknown X, you could compare it to both: A) a known sample of crude oil and B) a known uncontaminated sample of material (perhaps soil) to see which it matches best. Ideally, it should be compared to a range of possible references. For example, if it's possible the sample is heating oil or motor oil, you could compare it to similarly prepared samples of those as well. Some research has shown that vitamins A and E can produce fluorescence similar to petroleum products. Plot your samples Add all your scans to a set, so they can be viewed together. Your spectrometer should be calibrated and the very tall peaks from the laser light should align if this has been done correctly. Positive and negative controls Think critically about your testing. How could it have gone wrong? Could you have made mistakes, or is the match you've found between your unknown sample and your references not good enough? Could another material produce the same color spectrum as your suspected contaminant, and fool your test? (See this research on Vitamins E and A causing such false positives). Validate your results An extra step that may give your work more credibility is to submit a few of your samples for analysis to a lab, or to use other tests to confirm your results. Alternatively, if you know other testing has occurred, you can try to extend its results by re-testing the same site or samples, correlating your results with the previous test, and performing your own tests over a larger area or on more sites, or over a longer time span. Publish Ask others to critique your work or help you refine it on the plots-spectroscopy discussion list or by posting a research note thoroughly describing your results. Even if your work is not done, it's a great idea to share and solicit feedback on your plan before, during, and after you've done the work. You may be able to build on previous work on the website, and your work will help others who are seeking to perform similar tests. Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ on the ground, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Literature review Giger, Walter, and Max Blumer. "Polycyclic aromatic hydrocarbons in the environment. Isolation and characterization by chromatography, visible, ultraviolet, and mass spectrometry." Analytical chemistry 46.12 (1974): 1663-1671. http://pubs.acs.org/doi/abs/10.1021/ac60348a036 Pharr, Daniel Y., J. Keith McKenzie, and Aaron B. Hickman. "Fingerprinting petroleum contamination using synchronous scanning fluorescence spectroscopy." Groundwater 30.4 (1992): 484-489. http://onlinelibrary.wiley.com/doi/10.1111/j.1745-6584.1992.tb01523.x/abstract Parts list In progress: these are links to where you can buy parts to assemble your own oil testing kit Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made)	Revert
130	warren	July 23, 2014 00:14 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno, swabbing a street grate by @warren Preparing samples Use a cotton swab or small brush, dipped in mineral oil, to break up some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. Wear gloves before handling suspected pollutants. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Where possible, try not to put too much sand or other stuff in the jar. Save extra samples in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means (see Validate your results below). Seal the bottle tightly with the cap. You can then gently turn it over a few times to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Now that your sample is prepared, you may be able to get it to fluoresce by shining an ultraviolet light through it. We have had good results using a blue/UV laser, a 405 nanometer laser which is the same as found in a Blu-Ray player. See the parts list below for where to buy one. Strong UV LEDs can also work, but are not as bright. They are, however, easier to line up with a spectrometer's opening slit. Don't look at the laser too much, as it can hurt your eyes, even if you're not pointing it directly at your eye! Note that the laser will have a purpleish color by itself (as seen in the lead image at the top of the page) -- this is not fluorescence, but just scattering of the laser light. What you're looking for is any other color -- whitish, bluish, greenish -- which is not from the laser, but is produced in the material itself as it's excited by the UV light. To measure precisely the colors that are being produced, we will use a spectrometer. Spectrometry Colored light is often a blend of different colors. A spectrometer is a device which splits those colors apart, like a prism, and measures the strength of each color. A typical output of a spectrometer looks like this; [illustration of spectrometer plot] While there are many ways to use a spectrometer, in this case we can clearly see the laser color, or wavelength, which is only in a narrow range around 405 nanometers, to the left: [image here] All the remaining light, to the right of that tall peak, is produced by the excited material in the sample. The shape of that curve can be matched against other samples to help us identify what ours is. Construct a spectrometer different kits, download still under development Illuminate the sample cover it! no room or daylight good exposure no clipping Refine your technique same concentration take several for each, label them smooth your data repeat twice through and ensure your same samples are similar (ref. parts & crafts sample) concentration is OK? Compare When identifying an oil, we are hoping to measure the color of fluorescence of the Poly-Aromatic Hydrocarbons (PAHs) in the sample. The best way to identify a sample would be to compare it to a selection of similarly-prepared known reference materials. For example, if you have unknown X, you could compare it to both: A) a known sample of crude oil and B) a known uncontaminated sample of material (perhaps soil) to see which it matches best. Ideally, it should be compared to a range of possible references. For example, if it's possible the sample is heating oil or motor oil, you could compare it to similarly prepared samples of those as well. Some research has shown that vitamins A and E can produce fluorescence similar to petroleum products. Plot your samples Add all your scans to a set, so they can be viewed together. Your spectrometer should be calibrated and the very tall peaks from the laser light should align if this has been done correctly. Positive and negative controls Think critically about your testing. How could it have gone wrong? Could you have made mistakes, or is the match you've found between your unknown sample and your references not good enough? Could another material produce the same color spectrum as your suspected contaminant, and fool your test? (See this research on Vitamins E and A causing such false positives). Validate your results An extra step that may give your work more credibility is to submit a few of your samples for analysis to a lab, or to use other tests to confirm your results. Alternatively, if you know other testing has occurred, you can try to extend its results by re-testing the same site or samples, correlating your results with the previous test, and performing your own tests over a larger area or on more sites, or over a longer time span. Publish Ask others to critique your work or help you refine it on the plots-spectroscopy discussion list or by posting a research note thoroughly describing your results. Even if your work is not done, it's a great idea to share and solicit feedback on your plan before, during, and after you've done the work. You may be able to build on previous work on the website, and your work will help others who are seeking to perform similar tests. Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ on the ground, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Literature review Giger, Walter, and Max Blumer. "Polycyclic aromatic hydrocarbons in the environment. Isolation and characterization by chromatography, visible, ultraviolet, and mass spectrometry." Analytical chemistry 46.12 (1974): 1663-1671. http://pubs.acs.org/doi/abs/10.1021/ac60348a036 Pharr, Daniel Y., J. Keith McKenzie, and Aaron B. Hickman. "Fingerprinting petroleum contamination using synchronous scanning fluorescence spectroscopy." Groundwater 30.4 (1992): 484-489. http://onlinelibrary.wiley.com/doi/10.1111/j.1745-6584.1992.tb01523.x/abstract Photo walkthrough This older tutorial walks through every step with photo illustrations. We are combining it with the more thorough guide above. Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
129	warren	July 23, 2014 00:13 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno, swabbing a street grate by @warren Preparing samples Use a cotton swab or small brush, dipped in mineral oil, to break up some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. Wear gloves before handling suspected pollutants. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Where possible, try not to put too much sand or other stuff in the jar. Save extra samples in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means (see Validate your results below). Seal the bottle tightly with the cap. You can then gently turn it over a few times to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Now that your sample is prepared, you may be able to get it to fluoresce by shining an ultraviolet light through it. We have had good results using a blue/UV laser, a 405 nanometer laser which is the same as found in a Blu-Ray player. See the parts list below for where to buy one. Strong UV LEDs can also work, but are not as bright. They are, however, easier to line up with a spectrometer's opening slit. Don't look at the laser too much, as it can hurt your eyes, even if you're not pointing it directly at your eye! Note that the laser will have a purpleish color by itself (as seen in the lead image at the top of the page) -- this is not fluorescence, but just scattering of the laser light. What you're looking for is any other color -- whitish, bluish, greenish -- which is not from the laser, but is produced in the material itself as it's excited by the UV light. To measure precisely the colors that are being produced, we will use a spectrometer. Spectrometry Colored light is often a blend of different colors. A spectrometer is a device which splits those colors apart, like a prism, and measures the strength of each color. A typical output of a spectrometer looks like this; [illustration of spectrometer plot] While there are many ways to use a spectrometer, in this case we can clearly see the laser color, or wavelength, which is only in a narrow range around 405 nanometers, to the left: [image here] All the remaining light, to the right of that tall peak, is produced by the excited material in the sample. The shape of that curve can be matched against other samples to help us identify what ours is. Construct a spectrometer different kits, download still under development Illuminate the sample cover it! no room or daylight good exposure no clipping Refine your technique same concentration take several for each, label them smooth your data repeat twice through and ensure your same samples are similar (ref. parts & crafts sample) concentration is OK? Compare When identifying an oil, we are hoping to measure the color of fluorescence of the Poly-Aromatic Hydrocarbons (PAHs) in the sample. The best way to identify a sample would be to compare it to a selection of similarly-prepared known reference materials. For example, if you have unknown X, you could compare it to both: A) a known sample of crude oil and B) a known uncontaminated sample of material (perhaps soil) to see which it matches best. Ideally, it should be compared to a range of possible references. For example, if it's possible the sample is heating oil or motor oil, you could compare it to similarly prepared samples of those as well. Some research has shown that vitamins A and E can produce fluorescence similar to petroleum products. Plot your samples Add all your scans to a set, so they can be viewed together. Your spectrometer should be calibrated and the very tall peaks from the laser light should align if this has been done correctly. Positive and negative controls Think critically about your testing. How could it have gone wrong? Could you have made mistakes, or is the match you've found between your unknown sample and your references not good enough? Could another material produce the same color spectrum as your suspected contaminant, and fool your test? (See this research on Vitamins E and A causing such false positives). Validate your results An extra step that may give your work more credibility is to submit a few of your samples for analysis to a lab, or to use other tests to confirm your results. Alternatively, if you know other testing has occurred, you can try to extend its results by re-testing the same site or samples, correlating your results with the previous test, and performing your own tests over a larger area or on more sites, or over a longer time span. Publish Ask others to critique your work or help you refine it on the plots-spectroscopy discussion list or by posting a research note thoroughly describing your results. Even if your work is not done, it's a great idea to share and solicit feedback on your plan before, during, and after you've done the work. You may be able to build on previous work on the website, and your work will help others who are seeking to perform similar tests. Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ on the ground, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Literature review Giger, Walter, and Max Blumer. "Polycyclic aromatic hydrocarbons in the environment. Isolation and characterization by chromatography, visible, ultraviolet, and mass spectrometry." Analytical chemistry 46.12 (1974): 1663-1671. http://pubs.acs.org/doi/abs/10.1021/ac60348a036 Pharr, Daniel Y., J. Keith McKenzie, and Aaron B. Hickman. "Fingerprinting petroleum contamination using synchronous scanning fluorescence spectroscopy." Groundwater 30.4 (1992): 484-489. http://onlinelibrary.wiley.com/doi/10.1111/j.1745-6584.1992.tb01523.x/abstract Photo walkthrough This older tutorial walks through every step with photo illustrations. We are combining it with the more thorough guide above. Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
128	warren	July 23, 2014 00:04 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno, swabbing a street grate by @warren Preparing samples Use a cotton swab or small brush, dipped in mineral oil, to break up some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. Wear gloves before handling suspected pollutants. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Where possible, try not to put too much sand or other stuff in the jar. Save extra samples in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means (see Validate your results below). Seal the bottle tightly with the cap. You can then gently turn it over a few times to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Now that your sample is prepared, you may be able to get it to fluoresce by shining an ultraviolet light through it. We have had good results using a blue/UV laser, a 405 nanometer laser which is the same as found in a Blu-Ray player. See the parts list below for where to buy one. Strong UV LEDs can also work, but are not as bright. They are, however, easier to line up with a spectrometer's opening slit. Don't look at the laser too much, as it can hurt your eyes, even if you're not pointing it directly at your eye! Note that the laser will have a purpleish color by itself (as seen in the lead image at the top of the page) -- this is not fluorescence, but just scattering of the laser light. What you're looking for is any other color -- whitish, bluish, greenish -- which is not from the laser, but is produced in the material itself as it's excited by the UV light. To measure precisely the colors that are being produced, we will use a spectrometer. Spectrometry Colored light is often a blend of different colors. A spectrometer is a device which splits those colors apart, like a prism, and measures the strength of each color. A typical output of a spectrometer looks like this; [illustration of spectrometer plot] While there are many ways to use a spectrometer, in this case we can clearly see the laser color, or wavelength, which is only in a narrow range around 405 nanometers, to the left: [image here] All the remaining light, to the right of that tall peak, is produced by the excited material in the sample. The shape of that curve can be matched against other samples to help us identify what ours is. Construct a spectrometer different kits, download still under development Illuminate the sample cover it! no room or daylight good exposure no clipping Refine your technique same concentration take several for each, label them smooth your data repeat twice through and ensure your same samples are similar (ref. parts & crafts sample) concentration is OK? Compare When identifying an oil, we are hoping to measure the color of fluorescence of the Poly-Aromatic Hydrocarbons (PAHs) in the sample. The best way to identify a sample would be to compare it to a selection of similarly-prepared known reference materials. For example, if you have unknown X, you could compare it to both: A) a known sample of crude oil and B) a known uncontaminated sample of material (perhaps soil) to see which it matches best. Ideally, it should be compared to a range of possible references. For example, if it's possible the sample is heating oil or motor oil, you could compare it to similarly prepared samples of those as well. Some research has shown that vitamins A and E can produce fluorescence similar to petroleum products. Plot your samples Add all your scans to a set, so they can be viewed together. Your spectrometer should be calibrated and the very tall peaks from the laser light should align if this has been done correctly. Positive and negative controls Think critically about your testing. How could it have gone wrong? Could you have made mistakes, or is the match you've found between your unknown sample and your references not good enough? Could another material produce the same color spectrum as your suspected contaminant, and fool your test? (See this research on Vitamins E and A causing such false positives). Validate your results An extra step that may give your work more credibility is to submit a few of your samples for analysis to a lab, or to use other tests to confirm your results. Alternatively, if you know other testing has occurred, you can try to extend its results by re-testing the same site or samples, correlating your results with the previous test, and performing your own tests over a larger area or on more sites, or over a longer time span. Publish Ask others to critique your work or help you refine it on the plots-spectroscopy discussion list or by posting a research note thoroughly describing your results. Even if your work is not done, it's a great idea to share and solicit feedback on your plan before, during, and after you've done the work. You may be able to build on previous work on the website, and your work will help others who are seeking to perform similar tests. Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ on the ground, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Literature review Giger, Walter, and Max Blumer. "Polycyclic aromatic hydrocarbons in the environment. Isolation and characterization by chromatography, visible, ultraviolet, and mass spectrometry." Analytical chemistry 46.12 (1974): 1663-1671. http://pubs.acs.org/doi/abs/10.1021/ac60348a036 Pharr, Daniel Y., J. Keith McKenzie, and Aaron B. Hickman. "Fingerprinting petroleum contamination using synchronous scanning fluorescence spectroscopy." Groundwater 30.4 (1992): 484-489. http://onlinelibrary.wiley.com/doi/10.1111/j.1745-6584.1992.tb01523.x/abstract Photo walkthrough This older tutorial walks through every step with photo illustrations. We are combining it with the more thorough guide above. Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
127	warren	July 22, 2014 23:59 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno Preparing samples Use a cotton swab or small brush, dipped in mineral oil, to break up some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. Wear gloves before handling suspected pollutants. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Where possible, try not to put too much sand or other stuff in the jar. Save extra samples in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means (see Validate your results below). Seal the bottle tightly with the cap. You can then gently turn it over a few times to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Now that your sample is prepared, you may be able to get it to fluoresce by shining an ultraviolet light through it. We have had good results using a blue/UV laser, a 405 nanometer laser which is the same as found in a Blu-Ray player. See the parts list below for where to buy one. Strong UV LEDs can also work, but are not as bright. They are, however, easier to line up with a spectrometer's opening slit. Don't look at the laser too much, as it can hurt your eyes, even if you're not pointing it directly at your eye! Note that the laser will have a purpleish color by itself (as seen in the lead image at the top of the page) -- this is not fluorescence, but just scattering of the laser light. What you're looking for is any other color -- whitish, bluish, greenish -- which is not from the laser, but is produced in the material itself as it's excited by the UV light. To measure precisely the colors that are being produced, we will use a spectrometer. Spectrometry Colored light is often a blend of different colors. A spectrometer is a device which splits those colors apart, like a prism, and measures the strength of each color. A typical output of a spectrometer looks like this; [illustration of spectrometer plot] While there are many ways to use a spectrometer, in this case we can clearly see the laser color, or wavelength, which is only in a narrow range around 405 nanometers, to the left: [image here] All the remaining light, to the right of that tall peak, is produced by the excited material in the sample. The shape of that curve can be matched against other samples to help us identify what ours is. Construct a spectrometer different kits, download still under development Illuminate the sample cover it! no room or daylight good exposure no clipping Refine your technique same concentration take several for each, label them smooth your data repeat twice through and ensure your same samples are similar (ref. parts & crafts sample) concentration is OK? Compare When identifying an oil, we are hoping to measure the color of fluorescence of the Poly-Aromatic Hydrocarbons (PAHs) in the sample. The best way to identify a sample would be to compare it to a selection of similarly-prepared known reference materials. For example, if you have unknown X, you could compare it to both: A) a known sample of crude oil and B) a known uncontaminated sample of material (perhaps soil) to see which it matches best. Ideally, it should be compared to a range of possible references. For example, if it's possible the sample is heating oil or motor oil, you could compare it to similarly prepared samples of those as well. Some research has shown that vitamins A and E can produce fluorescence similar to petroleum products. Plot your samples Add all your scans to a set, so they can be viewed together. Your spectrometer should be calibrated and the very tall peaks from the laser light should align if this has been done correctly. Positive and negative controls Think critically about your testing. How could it have gone wrong? Could you have made mistakes, or is the match you've found between your unknown sample and your references not good enough? Could another material produce the same color spectrum as your suspected contaminant, and fool your test? (See this research on Vitamins E and A causing such false positives). Validate your results An extra step that may give your work more credibility is to submit a few of your samples for analysis to a lab, or to use other tests to confirm your results. Alternatively, if you know other testing has occurred, you can try to extend its results by re-testing the same site or samples, correlating your results with the previous test, and performing your own tests over a larger area or on more sites, or over a longer time span. Publish Ask others to critique your work or help you refine it on the plots-spectroscopy discussion list or by posting a research note thoroughly describing your results. Even if your work is not done, it's a great idea to share and solicit feedback on your plan before, during, and after you've done the work. You may be able to build on previous work on the website, and your work will help others who are seeking to perform similar tests. Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ on the ground, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Literature review Giger, Walter, and Max Blumer. "Polycyclic aromatic hydrocarbons in the environment. Isolation and characterization by chromatography, visible, ultraviolet, and mass spectrometry." Analytical chemistry 46.12 (1974): 1663-1671. http://pubs.acs.org/doi/abs/10.1021/ac60348a036 Pharr, Daniel Y., J. Keith McKenzie, and Aaron B. Hickman. "Fingerprinting petroleum contamination using synchronous scanning fluorescence spectroscopy." Groundwater 30.4 (1992): 484-489. http://onlinelibrary.wiley.com/doi/10.1111/j.1745-6584.1992.tb01523.x/abstract Photo walkthrough This older tutorial walks through every step with photo illustrations. We are combining it with the more thorough guide above. Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
126	warren	July 22, 2014 23:37 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno Preparing samples Use a cotton swab or small brush, dipped in mineral oil, to break up some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. Wear gloves before handling suspected pollutants. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Where possible, try not to put too much sand or other stuff in the jar. Save extra samples in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means (see Validate your results below). Seal the bottle tightly with the cap. You can then gently turn it over a few times to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Compare When identifying an oil, we are hoping to measure the color of fluorescence of the Poly-Aromatic Hydrocarbons (PAHs) in the sample. The best way to identify a sample would be to compare it to a selection of similarly-prepared known reference materials. For example, if you have unknown X, you could compare it to both: A) a known sample of crude oil and B) a known uncontaminated sample of material (perhaps soil) to see which it matches best. Ideally, it should be compared to a range of possible references. For example, if it's possible the sample is heating oil or motor oil, you could compare it to similarly prepared samples of those as well. Some research has shown that vitamins A and E can produce fluorescence similar to petroleum products. Plot your samples Add all your scans to a set, so they can be viewed together. Your spectrometer should be calibrated and the very tall peaks from the laser light should align if this has been done correctly. Positive and negative controls Think critically about your testing. How could it have gone wrong? Could you have made mistakes, or is the match you've found between your unknown sample and your references not good enough? Could another material produce the same color spectrum as your suspected contaminant, and fool your test? (See this research on Vitamins E and A causing such false positives). Validate your results An extra step that may give your work more credibility is to submit a few of your samples for analysis to a lab, or to use other tests to confirm your results. Alternatively, if you know other testing has occurred, you can try to extend its results by re-testing the same site or samples, correlating your results with the previous test, and performing your own tests over a larger area or on more sites, or over a longer time span. Publish Ask others to critique your work or help you refine it on the plots-spectroscopy discussion list or by posting a research note thoroughly describing your results. Even if your work is not done, it's a great idea to share and solicit feedback on your plan before, during, and after you've done the work. You may be able to build on previous work on the website, and your work will help others who are seeking to perform similar tests. Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough This older tutorial walks through every step with photo illustrations. We are combining it with the more thorough guide above. Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
125	warren	July 22, 2014 23:23 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno Preparing samples Use a cotton swab or small brush, dipped in mineral oil, to break up some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. Wear gloves before handling suspected pollutants. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Where possible, try not to put too much sand or other stuff in the jar. Save extra samples in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means (perhaps like these). Seal the bottle tightly with the cap. You can then shake the bottle or turn it over to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Compare When identifying an oil, we are hoping to measure the color of fluorescence of the Poly-Aromatic Hydrocarbons (PAHs) in the sample. The best way to identify a sample would be to compare it to a selection of similarly-prepared known reference materials. For example, if you have unknown X, you could compare it to both: A) a known sample of crude oil and B) a known uncontaminated sample of material (perhaps soil) to see which it matches best. Ideally, it should be compared to a range of possible references. For example, if it's possible the sample is heating oil or motor oil, you could compare it to similarly prepared samples of those as well. Some research has shown that vitamins A and E can produce fluorescence similar to petroleum products. Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
124	warren	July 22, 2014 22:49 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno Preparing samples These should be collected in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means. But for the purposes of the Public Lab Oil Testing Kit, we recommend using cotton swabs or small brushes dipped in mineral oil to remove some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Seal the bottle tightly with the cap. You can then shake the bottle or turn it over to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Compare Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
123	warren	July 22, 2014 20:42 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno Preparing samples These should be collected in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means. But for the purposes of the Public Lab Oil Testing Kit, we recommend using cotton swabs or small brushes dipped in mineral oil to remove some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Seal the bottle tightly with the cap. You can then shake the bottle or turn it over to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Compare Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
122	warren	July 22, 2014 20:39 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Locating samples Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. But oil contamination takes many forms, from residue around a street drain, to a sheen or buildup on the surface of the water. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno Preparing samples These should be collected in glass jars and stored in a cool, dark place, as there may always be an opportunity to test them later with more expensive, official means. But for the purposes of the Public Lab Oil Testing Kit, we recommend using cotton swabs or small brushes dipped in mineral oil to remove some of the material and dissolve it in a small, square-sided glass jar of mineral or baby oil. You may need to rub the sample for a while to get it to dissolve. If it does not dissolve, there may be more aggressive ways to dissolve it. Seal the bottle tightly with the cap. You can then shake the bottle or turn it over to get the residue to dissolve -- it may take some time before the mineral oil takes on a distinct but faint yellowish hue. Concentration One big issue is getting the correct concentration of sample dissolved. If it's too little, we may not be able to get it to glow under UV light. Too much and it could be too dark for the light to be visible in the bottle. We recommend a darkness similar to very dilute tea: Labeling Label the bottle with the date, time, and location. If you also give it a unique number, any other information can be kept in a notebook next to that number, such as further notes on the location and its condition. Take a photo of the sample with your label, in the place you found the sample, for context. Scan Compare Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Dissolving samples We use mineral oil as it's non-toxic and cheap, and can be purchased in most pharmacies as either mineral oil or "baby oil". However, some samples may be hard enough that they don't dissolve readily, and more aggressive solvents may be able to dissolve these, such as methanol or denatured alcohol. These are not as safe to handle, however, so we advise caution if you attempt this. Please post a research note if you attempt this, as it is an unexplored area. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
121	warren	July 22, 2014 20:23 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Originally, we focused on tar balls which were washing up on US Gulf Coast shorelines following the BP oil spill. These ranged from hard black lumps to orange residue. Here are some examples: Left to right: dried oil on rocks in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, oil residue in the ocean in 2010, Louisiana coast by Cesar Harada CC-BY-NC-SA, Oil tanker leak on tracks beside Mississippi River, by @marlokeno Scan Compare Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
120	warren	July 22, 2014 19:45 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Scan Compare Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
119	warren	July 22, 2014 19:30 \| over 10 years ago Introduction The Oil Testing Kit is an open source Do-It-Yourself kit which attempts to make it possible to identify oil pollution by type. This means matching a suspected sample with a known sample of crude oil, motor oil, heating oil, or other petroleum-based contaminant using a homemade fluorescence spectrometer, which measures the color of light emitted by carefully prepared samples when they are illuminated with strong ultraviolet light, as shown above. Collect, Scan, Compare The process of testing for oils can be described in three overall steps; collecting samples of suspected oil or tar from the ground, and dissolving small amounts in mineral oil so they are transparent illuminating the solutions with ultraviolet light -- presently using a 405 nanometer blue laser -- and recording the light spectrum with a DIY spectrometer comparing the spectrum to those of similarly prepared samples of known pollutant oils, as well as a negative control Here we will discuss and illustrate these steps in depth. Collect Scan Compare Variations There are many variations of the process which could be useful. These include: collecting samples from a sheen on the surface of the water -- which may be difficult as sheens are extremely thin and spread out measuring fluorescence in-situ, without collecting or concentrating samples in a jar -- which could be difficult as it's very dilute and mixed with other things like water, dirt, or plant matter Many of these may be future goals of the project, but we are focusing on our primary use case of collecting contaminated soil or residue from the ground, dissolving it in mineral oil, and illuminating it with UV in a spectrometer. Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
118	stevie	July 15, 2014 19:35 \| over 10 years ago Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm http://www.freundcontainer.com/french-square-glass-bottles/p/v4225B01/ 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
117	stevie	July 15, 2014 19:34 \| over 10 years ago Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html http://www.ebottles.com/showbottles-bottle-1556-kw-ELIQUID_VIALS.htm http://www.ebottles.com/showbottles-bottle-1329-gclid-Cj0KEQjwopOeBRC1ndXgnuvx8JYBEiQAq4RPt_MBIoRstpRXJzK66iXV1lbaZ6J7TWOot8oR6wDas7QaAops8P8HAQ-kw-NAIL_POLISH_BOTTLES_WITH_BRUSHES___GLASS.htm 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
116	warren	June 26, 2014 18:51 \| over 10 years ago Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon! Misc images	Revert
115	Shannon	June 23, 2014 20:24 \| over 10 years ago Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon!	Revert
114	Shannon	June 23, 2014 20:24 \| over 10 years ago Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon!	Revert
113	warren	June 07, 2014 19:24 \| over 10 years ago Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon!	Revert
112	warren	June 07, 2014 19:19 \| over 10 years ago Alpha program We've sent out about 20 prototype "alpha" kits to people around the US to give the oil test kit a try, and refine it to get ready for a bigger release. If you have one please share what you've done with it and post any ideas, feedback, complaints, suggestions, questions and modifications you have by using this button: Post about your alpha oil testing kit Photo walkthrough Collect everything shown above: mineral oil, swabs, jars, dropper, and a desktop spectrometer. Use the dropper to fill a jar with mineral oil. The dropper can become the oil jar's new top! Convenient. Don't get that dropper dirty! Swab and slightly dissolve some residue, which could be on the ground, on a beach, by a sewer drain, and put it in the jar. Where possible, try not to put too much sand or other stuff in the jar. Wear gloves. It helps if the swab is first wet with mineral oil. You can move the swab around to dissolve the residue. You're going for a nearly clear color, with just a slight brown tinge. Seal the bottle, and gently turn it over a bunch of times to help the residue dissolve into the mineral oil. You may then have to wait for the sediment to settle out. You want the liquid to be quite transparent, with the chunky stuff settled to the bottom. Shine the blue/violet/UV laser through to see if the material now fluoresces. This sample worked really well! Label the jar and take good notes about where you got the material and when. Place it in a box (you can use the desktop spectrometer box itself -- see Mathew L's research note) and illuminate it with the laser again, and save the result in SpectralWorkbench.org. Coming soon: save the spectrum and try to get it bright enough for the highest point of the curve to fall between 25-75% intensity. Illustrations For the illustrated guide: Related link to spectral challenge draft graphics: https://github.com/jywarren/spectralchallenge/issues/4 Parts list Possible upgrade: nail polish bottles, with built-in bottlecap-swabs. An all-in-one, one-use pre-filled with mineral oil! Maybe you break off the swab and throw it away, or maybe it doesn't matter. http://www.alibaba.com/product-detail/nail-polish-bottles_862081740.html?s=p http://www.alibaba.com/product-detail/10ml-empty-square-nail-polish-bottle_1042482910.html?s=p http://www.alibaba.com/product-detail/0-4oz-Art-Nail-Polish-Bottle_674230480.html 5oz mineral oil (baby oil -- the added fragrance doesn't fluoresce): $3 - http://www.amazon.com/Johnson-Baby-Oil-Kids-Ounce/dp/B000GCJM06/ an eyedropper: $0.05 0 http://www.sciplus.com/p/CAP-WDROPPER_39038 a 405nm blue/violet laser pen: $3 http://www.alibaba.com/product-gs/700677050/well_tested_405_nm_blue_laser.html, or http://www.ebay.com/itm/like/350812684726?lpid=82 to buy just one cuvettes 4 flat-sided jars: $0.35 each - http://www.sciplus.com/p/WHITCAP-BOTTLE_48212 cotton swabs: $0.10 olive oil test sample: $0.17 paper instructions (yet to be made) Draft instructions The basic instructions will be something like: Put on latex or nitrile gloves Wet a cotton swab with mineral oil Rub it on the sample -- a suspected tarball or lump of oily residue -- until it gets brownish (it could take a little while for it to dissolve) Dip the dirty swab (that's like a pirate insult... :-P) in one of the square bottles which has been filled 2/3 with mineral oil, and repeatedly and gently dunk it until the brown stuff dissolves and "taints" the mineral oil. Keep dunking until it looks like a very very weak tea -- so you can see the coloration. We need to come up with a standard way to determine how dark... maybe a printed comparison strip? Cap the square jar and throw away the cotton swab (bag it if it's really gross). Throw away the gloves and wash your hands Then, inside your spectrometer box (to reduce stray light and to protect your eyes from the laser light): Without looking at the laser light directly (it's bad for your eyes!!!), shine the laser through a hole in your box, so the laser shines through your jar perpendicular to the spectrometer opening. We'll illustrate this better but look at the Parts & Crafts note above. Move the laser up and down until you see both the bright laser peak on your SpectralWorkbench.org graph, as well as the broader range of colors that are the fluorescence. NE Barnraising brainstorm We had a session to reinvent the oil test kit guide at the Northeast Barnraising. More details soon!	Revert