Public Lab Wiki documentation



Video Spectrometer Construction

This is a revision from February 22, 2012 23:03. View all revisions
4 | 51 | | #528

Line up the camera lens with your drawn guideline

Introduction

This page documents the construction of the video spectrometer. For usage, see video spectrometer usage. For drafts and older instructions, see video spectrometer construction drafts.

This hardware design will soon be released under the CERN Open Hardware License 1.1. A draft agreement is under development here: http://publiclaboratory.org/wiki/ohl-agreement and should be complete in a few days.

If you have trouble, see Video Spectrometer Troubleshooting

To remove the filter, see Webcam Filter Removal

Video instructions

This 10 minute video walks through a simplified but effective version of the video spectrometer. It results in a visible-range spectrometer, but can be modified later for infrared range data:

Full step-by-step instructions

Construction using these steps takes approx. 1 hour. Open-source software to operate this spectrometer is available at: http://github.com/jywarren/spectral-workbench

Everything necessary (more or less) to make a DIY Spectrometer

Materials

Everything necessary to make a DIY Spectrometer (let's try to reduce this list!):

  • a black VHS case like from Blockbuster - $0.50
  • a straight-edge
  • scissors
  • X-acto knife
  • a pen
  • black tape (gaffe or electrical)
  • white glue
  • hot glue and a hot glue gun
  • a letter or A4-sized sheet of stiff black card paper - $0.50
  • a DVD-R - $0.50
  • a USB webcam, preferably over 640x480/VGA resolution, 780 HD is best (like this one for $25 or this one for $8)
  • a computer

Optional:

Construction

Make a base card

1. Make a base card

Cut a flat piece of black card (the stiffer the better!) and glue or double-sided tape it to the bottom of your VHS case.

Use some proprietary software (packaging) to draw a straight line

2. Use some proprietary software (packaging) to draw a straight line

This will be the path of your beam of light, so it should allow room for a webcam at one end, and a narrow slot at the other. I drew it a little closer to the outer edge of the case, maybe 2" from the edge.

Adobe Creative Suite is so great for drawing straight lines! ;-)

Cut a 2x3 square piece of black cardstock where each square is 7/8" x 7/8"

3. Cut a 1 3/4" x 2 5/8" piece of black cardstock, divided into six 7/8" squares

Cut and crease it as shown so you can make a stable box-like shape. Cut an extra bit of 7/8"-long card as shown -- this will be used to make a very narrow slot. Be sure the sides of the slot and the extra bit are completely straight! Use a straight-edge.

This is the "bracket" for your precision slot.

Glue the strip onto your bracket to make a very precise slot

4. Glue the strip onto your bracket to make a very precise slot

It should be less then 1mm wide. You can use a piece of card paper to keep a consistent width, but I prefer to eyeball it. If you use just a tiny bit of white glue, it should give you a few seconds to get it right before it's too dry to move. Let this dry thoroughly before continuing.

Check your precise slot by looking through it at a light

5. Check your precise slot by looking through it at a light

The slot should be roughly centered, horizontally, and should extend to within 3-4mm of either the top and bottom. It should be of even width, a bit less than a millimeter.

Cut a hole centered on the guideline you drew

6. Cut a hole centered on the guideline you drew

It should be as tall as your slot but leave enough plastic to remain stiff. You can use a big drill bit here too if it's easier.

Glue your slot in so it covers the hole you cut

7. Glue your slot in so it covers the hole you cut

You'll have to bend the center flap under so that the slot directly abuts the hole. Make sure it lines up with the light beam guideline you drew.

Unscrew the lens and look for the reddish/bluish infrared filter

8. Unscrew the lens and look for the reddish/bluish infrared filter

On most webcams, you should be able to remove the lens without opening the case.

Slide a knife under the filter and pop it out, then screw the lens back in

9. Slide a knife under the filter and pop it out, then screw the lens back in

You can throw the filter away; we won't be needing it.

Look at a barcode through the webcam to determine its range of focus

10. Look at a barcode through the webcam to adjust its range of focus

Rotate the camera lens to adjust the focus. You may need to gently use a pair of needle-nosed pliers at first. Anything between around 4-11 inches away from the lens should be in focus. This means your slot will be in focus when it's installed opposite the camera.

Turn the camera lens to focus it

11. Turn the camera lens to focus it

A barcode is a nice test since it has many fine lines -- just like the spectra will have. It should be in focus at about 8" away from the camera.

Cut a piece of DVD-R and peel it apart carefully

12. Cut a piece of DVD-R and peel it apart carefully

Don't get any fingerprints on it! The DVD piece should be in the orientation shown -- so that the "track lines" of the DVD-R remain vertical in the camera's image. You won't be able to see the lines, so keep track of them as you make the cut and get ready to attach it to the camera.

Once you cut the DVD-R piece, you should be able to split the layers apart using the tip of an X-acto knife. Choose the most transparent part.

Separate the 2 layers, and choose the lower, more transparent one

13. Separate the 2 layers, and choose the lower, more transparent one

Cut out a small rectangle of DVD, keeping the track lines vertical

14. Cut out a small rectangle of DVD, keeping the track lines vertical

Choose a clear area with no fingerprints or chips of reflective material.

Tape or glue the DVD-R bit in front of the lens

15. Tape or glue the DVD-R bit in front of the lens

Here I covered the camera too, since it has built-in LED lights which would interfere with our readings.

Mount your camera

16. Mount your camera

Use hot glue or something similar to firmly and sturdily mount your camera on a piece of card (cut similarly to your slot). How you do this will vary depending on your webcam but it should be horizontal and pointed straight . This can be tough -- a lot of hot glue can be helpful.

Position the webcam to point 40 degrees away from the slot

17. Position the webcam to point 40 degrees away from the slot

This varies by camera, so don't glue it down yet.

Line up the camera lens with your drawn guideline

18. Line up the camera lens with your drawn guideline

For this camera, it was at 50 degrees away from pointing straight at the slot. See the following step for a protractor you can use to measure.

A protractor

18a. Protractor

Print this or trace it to measure the angle of your camera.

Adjust the angle of the camera so that you can see the whole spectrum

19. Adjust the angle of the camera so that you can see the whole spectrum

Even with the top open, you can see that there are finer lines (indicating good focus and a narrow, precise slot) and see the range of colors. An angle of 40 degrees away from the slot should be good but you may need to make finer adjustments, and it varies by camera. Once you have it, glue the camera in place and secure it with a lot of hot glue.

Knot the USB cable and tape it in place

20. Knot the USB cable and tape it in place

Leave a couple inches of slack in the box. You can cut a small hole for the cable to exit the box; the knot assures that the camera is not disturbed even if you yank the cable.

Close off any potential light leaks with dark tape

21. Close off any potential light leaks with dark tape

Boot up the Spectral Workbench software to see a spectrum

22. Boot up the Spectral Workbench software to see a spectrum

http://github.com/jywarren/spectral-workbench

You may have to press the up/down arrows to choose the height you're sampling from. Press Tab to choose the calibration mode which will help you line things up.

A completed spectrometer

23. A completed spectrometer

I added a blue tape with an arrow so you know where the slot is, and mounted it on an old LCD monitor stand. Pro-fessional!

Using your spectrometer

The PLOTS Spectral Workbench software is not yet complete, but with a little configuration you should be able to get it running and start saving spectra. A video on how to use the spectrometer is coming soon.

Consider purchasing a microphone stand and clip for $14.

Design refinements

The design is still being modified and improved. If you have ideas for how to make it better, chip in on the mailing list. Some ideas are listed here; feel free to contribute:

  • The webcam mounting is not the most stable. What about using friendly plastic, which softens and becomes moldable in warm water, to create a very sturdy base for the camera? In a kit, we could ship an ounce or two for a couple dollars. 28 oz = $50. If it goes wrong you can always warm it up again.