Comments

Author Comment Last activity Moderation
tonyc "The settings I used for the above time lapse, from the config file for mobius camera: Photo Set Time Lapse Shooting=[8],0:off,1:0.25s,2:0.5s,3:1s,..." | Read more » about 8 years ago
tonyc "those are mms, on the measuring tape, btw. Guess I cropped the most important part scale out of the photo! " | Read more » about 8 years ago
tonyc "this is set up to use light from above, so had to force it to get an image on an opaque object. it think there is a lot of room to get better magn..." | Read more » about 8 years ago
tonyc " waterscope_optics_module.pdf Using a Pi cam and some optics from alibaba that runs about $20, you can get sub-micron quality. This image made..." | Read more » about 8 years ago
tonyc "This is so cool, it hurts a little. Did you run GPS while you took the photos? I have to try this! " | about 8 years ago
tonyc " hasn't lost a drop! " | Read more » over 8 years ago
tonyc " Tried drilling through bottle cap, then making the hole really jagged using an awl. Then a pen tube through a rubber stopper, thick layer of sili..." | Read more » over 8 years ago
tonyc "I don't follow. Are you saying they will work, and drop the mic in a "hellz-yeah" way? or are you saying they won't work and drop the mic like a Ni..." | Read more » over 8 years ago
tonyc "I ordered these lamp rods, some of the threaded cable penetrators, and some silicone tubes to the pdx office. The blue robotics folks say steep bul..." | Read more » over 8 years ago
tonyc "Very cool to see what they came up with. I see they are using the velcro cable ties on the pole mount. And that they'd cut the zip tie at the end o..." | Read more » over 8 years ago
tonyc "Good points. the main thrust of developing extreme low cost rigs is to be able to add them easily to the existing Balloon kit and kite kits, offeri..." | Read more » over 8 years ago
tonyc " This is hacky as all getout, but the general idea of a rig for oblique panos from a kit box is one that @mathew mocked up recently, and this s..." | Read more » over 8 years ago
tonyc "I wonder how much motion it would get on a simple flight without jostling it at all. This is such a great idea, allowing for chaotic energy to get ..." | Read more » over 8 years ago
tonyc "I wanted to verify the paperclip wasn't in danger of shorting anything out inside the camera, so opened it up to find it can come in contact with t..." | Read more » over 8 years ago
tonyc "These are both great, and an excellent video summary of the questions you are facing here. My mind goes into a place of splitting the designs into..." | Read more » over 8 years ago
tonyc "Here's one photo with the day's work in one place: " | Read more » over 8 years ago
tonyc " " | Read more » over 8 years ago
tonyc "One more: based on @gvillasenor work I found laying on the desk, got idea for simple lens/camera protection. Using a solo cup (jello shot sized)..." | Read more » over 8 years ago
tonyc "It does come with the holder, and I've been playing a bit with the tripod socket and finding ways to use it without throwing the balance out. I ag..." | Read more » over 8 years ago
tonyc "Update on this: hardware testing is on hold while we ship these back to our fab to work on the procedure for flashing firmware on their end. We're ..." | Read more » over 8 years ago
tonyc "You can't really see it all in one shot, so here's this gratuitous closeup vid: " | Read more » over 8 years ago
tonyc " Here you can see the addition of some zip ties to provide a stop-gap to the things sliding down too far. These are put on same way as with ..." | Read more » over 8 years ago
tonyc "I've had an idea of a rig made from a chinese togo container and chopsticks for a while. I made one, but the container was not robust enough at the..." | Read more » over 8 years ago
tonyc "Cern licence is on there: " | Read more » over 8 years ago