The status of Public Lab's 10 MakerBot Replicators.

• Public Lab office, Propeller Workspace, 4035 Washington Ave, New Orleans, LA

  • Contact: Shannon Dosemagen

  • SN______ on loan

    • Projects:
    • Maintenance:
  • SN______ on loan
    • Projects:
    • Maintenance:
  • SN _____ not operational
    • Projects:
    • Maintenance:
      .

• Picayune, MS

  • Contact: Dan Beavers: danbeavers at organizers dot publiclab dot org
  • SN______
  • Projects:
  • Maintenance:
    • Arrived with both extruders upgraded to the spring loaded roller type (no delrin plungers).
    • Left extruder inoperable due to cable break that I just have not fixed yet.
    • The 5 volt power upgrade has not been performed yet.
      .

• Geography Department, University of Kentucky

  • Contact: Jessi Breen
  • SN______ not operational
  • Projects:
  • Maintenance:
    .

• Public Lab office, Brooklyn, NY, Former Pfizer building, 630 Flushing Avenue

  • Contact: Liz Barry
  • SN_____ not operational
  • Projects:
  • Maintenance:
    .

• Parts and Crafts, Sommerville, MA

  • Contact Katie and Will
  • SN_____
  • Projects:

  • Maintenance:

    .

• Hackrfarm/University of Massachusetts

  • Contact: Ian Walls
  • SN_______
  • Projects:
  • Maintenance:
    .

• LEAFFEST HQ, Salisbury, VT

  • Contact: Chris Fastie whose gmail is cfastie
  • SN 11837

  • Build hours:

    • Initial build hours 12/2013: 11
    • build hours on 02/07/2014: 245
    • build hours on 08/18/2014: 640
    • build hours on 01/01/2015: 1000
    • build hours on 02/08/2015: 1200

  • Projects:

    • Prototyping camera rigs for aerial mapping
    • Experimenting with producing camera rigs for sale to Public Lab mappers
    • Prototyping spectrometer

  • Maintenance:
    

    • tightened all hex bolts holding plywood frame together 12/2014
    • upgraded firmware to Makerbot v. 7.5
    • broken fan replaced 12/24/2013
    • new nozzles installed 01/04/2014
    • 24v/5v regulator replaced 01/17/2014
    • Filament feed mechanism upgraded (all prints were failing) (MakerBot replacement parts for right extruder) 02/06/2014
    • Filament feed mechanism for left extruder printed and installed with MakerBot hardware 04/2014
    • Printed feet, spool holders, and LCD/keypad cover
    • lubricated noisy fan in motherboard compartment with SuperLube 06/2014
    • Replaced x-axis motor cable (all prints were failing) 08/18/2014
    • x-axis idler pulley is lubricated every week with SuperLube.
    • Installed new ball bearing x-axis idler pulley from Alm Gear ($18). 01/20/2015
    • Tightened all hex bolts holding plywood frame together. They were all loose again after 1000 hours of printing. 01/21/2015
    • Tightened both grub screws on all six pulleys. They all tightened, but I noticed no difference in performance. 01/29/2015
    • Removed the fan from the motherboard compartment. It is not needed for cooling (long story) and just makes noise. 02/11/2015 .

• Public Lab retail fulfillment center, Portland, OR

  • Contact: Mathew Lippincott
  • SN 12328
  • Projects:
• 24v/5v regulator replaced 3/14
• spool holders replaced

• indicator LEDs disconnected to prevent voltage damage to board by motors.

  • Maintenance: